ASTM A153 / A153M - 16a. An ASTM designation number identifies a unique version of an ASTM standard. A153 / A153M - 16a. A = ferrous metals; 153 = assigned sequential number. M = SI units. 16 = year of original adoption (or, in the case of revision, the year of last revision) a = indicates subsequent revision in same year.
Ref. A153 Classes C or B Ref. A153 Classes C or B 2.0 mils 50 m 1.7 mils 43 m 1.7 mils 43 m F2329 Supplementary Requirement S1 A394 Bolts Ref. A153 Class C 2.1 mils 53 m Ref. A153 Class C 1.7 mils 43 m 2.8 mils 70 m 2.8 mils 70 m 2.5 mils 63 m Class D Fasteners, Diameter 3/8 in 1.7 mils 43 mClass D 1.4 mils 36 m
ASTM ASTM A153 [affil. link to spec at Techstreet] is for fasteners and other hardware small enough to centrifuge to remove excess zinc after dipping. No drips are allowed, and thicknesses are specified for threaded parts. The specifications overlap; threads on parts hot dipped per A123 must conform to A153. Ken Vlach [dec] researched responses.
Nov 01, 2016 ASTM A153/A153M, Revision 16A, November 1, 2016 - Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware This specification covers zinc coatings applied by the hot-dip process on iron and steel hardware. The hot-dip galvanizing process consists of parts being immersed in molten zinc for a sufficient time to allow a metallurgical reaction between iron from the
1.1 This specification covers zinc coatings applied by the hot-dip process on iron and steel hardware. The hot-dip galvanizing process consists of parts being immersed in molten zinc for a sufficient time to allow a metallurgical reaction between iron from the steel surface and the molten zinc, resulting in the formation of Zn/Fe alloy layers bonding the coating to the steel surface.
approved in 1933. Last previous edition approved in 2005 as A153/A153M - 05. DOI: 10.1520/A0153_A0153M-09. 2 For referenced ASTM standards, visit the ASTM website, astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards volume information, refer to the standard Document Summary page on the ASTM ...
Feb 25, 2011 ASTM A153. February 25, 2011. Authored by Bernardo A. Duran III. ASTM A153 governs zinc coatings applied by the hot-dip process to hardware products such as castings, fasteners, rolled, pressed, and forged products, and miscellaneous threaded objects that will be centrifuged, spun, or otherwise handled to remove excess zinc.
The specification ASTM A153/A153M applies to hardware products such as castings, fasteners, rolled, pressed, and forged products, and miscellaneous threaded objects that will be centrifuged, spun, or otherwise handled to remove excess zinc (Figure 12).The requirements for ASTM A153/A153M are very similar to those stated earlier for ASTM A123/A123M, except for the addition of threaded products ...
ASTM A153/A153M. Specification for Zinc Coating (Hot-Dip) on Iron and Hardware, applies to hardware products such as castings, fasteners, rolled, pressed, and forged products, and miscellaneous threaded objects that will be centrifuged, spun, or otherwise handled to remove the excess zinc. The requirements of this specification are very similar ...
Jul 19, 2011 ASTM A153 is the hot-dip galvanizing specification for hardware and fasteners that are spun or otherwise handled (torch and steel brush) after galvanizing to remove excess zinc. ASTM A123 is the hot-dip galvanizing specification for most other items (except single reinforcing bars).However, there is an instance when A123 is the appropriate specification to use when galvanizing steel parts ...
Feb 01, 2016 ASTM A153/A153M-01a. October 10, 2001 Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware 1.1 This specification covers zinc coatings applied by the hot-dip process on iron and steel hardware. 1.2 This specification is intended to be applicable to hardware items that are centrifuged or...
Shop Online. ASTM Standards. Several fasteners can be classified under ASTM standards. Some are listed below for your reference. Click any of the ASTM standard sheets below to download a PDF version. ASTM A36. ASTM A47. ASTM A48. ASTM A153.
Sep 01, 2017 1.4 The galvanizing of hardware items that are to be centrifuged or otherwise handled to remove excess zinc (such as bolts and similar threaded fasteners, castings and rolled, pressed and forged items) shall be in accordance with Specification A153/A153M. 1.5 Fabricated reinforcing steel bar assemblies are covered by the present specification.
ASTM International, 2011. Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire, ASTM A641-09a. ASTM International, 2009. Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware, ASTM A153-09. ASTM International, 2009.
astm a193 astm a307 astm a320 astm a453 : hot dip galvanised : is 1367 pt 13 is: 4759 bs en: 1461, astm a153 astm a123 black phosphate: is 1367 pt 12 electro galvanised : is: 1367 pt 11 , is: 1573 ptfe coating: astm d:3294
astm f436/f436m finish hot dip galvanised : is 1367 pt 13 is: 4759 bs en: 1461, astm a153 astm a123 black phosphate: is 1367 pt 12 electro galvanised : is: 1367 pt 11 , is: 1573 ptfe coating: astm d:3294
The American Galvanizers Association (AGA) is a non-profit trade association dedicated to serving the needs of after-fabrication galvanizers, fabricators, architects, specifiers, and engineers.
ASTM A193 defines both SI (Metric) and inch-pound units. Grade B7 is a heat-treated chromium-molybdenum low-alloy steel with minimum tensile strength requirement of 125 ksi (860 Mpa), yield 105 ksi (720 Mpa), and maximum hardness of 35HRC. Boltport uses Alloy Steel AISI 4140 bar stock or forging stock to produce B7 headed and non-headed bolts.
Kennedy Galvanizing, Inc. Kennedy Galvanizing is a job shop galvanizer and has been since march 4th, 1988. We specialize in spin but also do structural products up to 29 feet. We also pride ourselves on our expedited orders and have extraordinary turn around time
ASTM A53 B mechanical strength is the same with ASTM A106 B steel pipe, Tensile strength maximum 415 Mpa, Yield strength maximum 240 Mpa. Elongation: For A53 pipe there are 2 methods to calculate elongation. A: Use equation: e = 625 000 [1940] A^0.2/U^0.9. B: See ASTM A53 elongation value table X4.1 or table X4.2 for different specimen area.
A576 GR1015 Modified. 5/8 3/4. A36 or A675 GR60. 7/8. A36. FINISHES. All Channel nuts are available in: Electro-galvanized (EG), conforming to ASTM B633 type III SC1. Hot-dipped galvanized (HG), conforming to ASTM A153.
The ASTM F563 Pipe Clamps are manufactured to sustain very high pressure and product warranty.In 2015 we have stocked more than 188 tons of ASTM F563 Pipe Clamps in all sizes, to cater to immediate delivery and urgent needs of the clients.
You Are Here-> Home ->Specification->ASTM A436 Washers Specification. These ASTM F436 Washers are hardened steel washers for use with fasteners having nominal thread diameters of through 4 in. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners.
Galvanized to meet or exceed ASTM A153 or ASTM F2329 INCLUDES NUTS AND SAE WASHERS 1/2 X 8 BENT ANCHOR BOLT (HOT-DIPPED GALVANIZED) 2 PIECE PACKAGE Our Price: $3.89 . Used to anchor lumber to concrete. For use in exterior applications with all treated lumber. Conforms to ASTM
Feb 01, 2016 ASTM A153/A153M-01a. October 10, 2001 Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware 1.1 This specification covers zinc coatings applied by the hot-dip process on iron and steel hardware. 1.2 This specification is intended to be applicable to hardware items that are centrifuged or...
ASTM A153/A153M Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware. ASTM number. A167 (15) Title. ASTM A167 Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate Sheet and Strip. ASTM number. A185 (1) ...
ASTM International, 2011. Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire, ASTM A641-09a. ASTM International, 2009. Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware, ASTM A153-09. ASTM International, 2009.
Feb 10, 2020 Category: science chemistry. 4.4/5 (1,488 Views . 23 Votes) ASTM A153 is the hot-dip galvanizing specification for hardware and fasteners that are spun or otherwise handled (torch and steel brush) after galvanizing to remove excess zinc. A123 is appropriate when the fasteners or hardware have been welded onto a slate or other piece of steel.
ASTM A153-A153M-05 ()㈤€ (). ﹀. ぇぇ〃㈢1%€. ㄥやｏら︼︽ф50% ...
This is a list of ASTM International standards. Standard designations usually consist of a letter prefix and a sequentially assigned number. This may optionally be followed by a dash and the last two digits of the year in which the standard was adopted. Prefix letters correspond to the following subjects: A = Iron and Steel Materials
ASTM International (formerly known as American Society for Testing and Materials) is a global standards organization whose 30,000+ technical specialists create and maintain more than 13,000 standards. ASTM members represent more than 90 industries and develop standards for everything from airplanes to N-95 masks for more than 120 years.
The American Galvanizers Association (AGA) is a non-profit trade association dedicated to serving the needs of after-fabrication galvanizers, fabricators, architects, specifiers, and engineers.
18-8 Stainless Steel Heavy Hex HeadScrews for High-Pressure Applications. These Grade B8 screws are made from 18-8 stainless steel and have good chemical resistance. Also known as pressure bolts, they meet the high-pressure and high-temperature regulations of ASTM A193 and are used to secure pressure tanks, valves, and flanges.
Jun 21, 2017 ASTM A325€4902004630 ┒︿ у€€. у ㄥ. やASTM F1852 2.7ㄥ€ ...
A576 GR1015 Modified. 5/8 3/4. A36 or A675 GR60. 7/8. A36. FINISHES. All Channel nuts are available in: Electro-galvanized (EG), conforming to ASTM B633 type III SC1. Hot-dipped galvanized (HG), conforming to ASTM A153.
Unistrut P4007 P4008 P4009 P4010 Spring Nuts. Unistrut Channel Nuts with Springs allow you to easily attach Unistrut Channel and Fittings to one another. To be used with the following channels: P3300, P4000, P4400, P4520 and P4100.
ASTM A962 is a related specification that covers a group of common requirements as they relate to the A193 specification. Section 13 of the A962 specification addresses thread form and class. Threads shall comply with ASME B1.1, Class 2A and can be cut or rolled.
ASTM International is an organization of inclusion - offering global access to fully transparent standards development, resulting in the highest technical excellence in standardization. Initiated in 2001, ASTM Internationals Memorandum of Understanding program promotes: communication between signatory member standards bodies; awareness of each other standardization systems; development of ...
coatings shall conform to ASTM A153/A153M unless modified. 2.3 BRACES AND RAILS ASTM F1083 , zinc-coated, Group IA, steel pipe, size NPS 1-1/4. Group IC steel pipe, zinc-coated, shall meet the strength and coating requirements of ASTM F1043 . [Braces and rails shall be [Group IA] [Group IC], steel pipe, size NPS 1-1/4
Feb 25, 2011 ASTM A153. Share. February 25, 2011. ASTM A153 governs zinc coatings applied by the hot-dip process to hardware products such as castings, fasteners, rolled, pressed, and forged products, and miscellaneous threaded objects that will be centrifuged, spun, or
ASTM A153/A153M-16a Red Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware (Standard + Redline PDF Bundle) 1.1 This specification covers zinc coatings applied by the hot-dip process on iron and steel hardware. The hot-dip galvanizing process consists of parts being immersed in molten zinc for a sufficient time to allow ...
Requirements for the sampling of these fasteners can be found in F2329/F2329M. 1.4 ,This specification is applicable to orders in either inch-pound units (as A153) or in SI units (as A153M ). Inch-pound units and SI units are not necessarily exact equivalents. Within the text of this specification and where appropriate, SI units are shown in ...
ASTM A1008/A1008M Zinc coating: ASTM A153/A153M-B2 Class B (sheet metal ties and anchors hot-dip galvanized after fabrication). Sheet Metal (Stainless Steel): ASTM A 666, ASTM A480/480M, and ASTM A240/A240M AISI Type 304 or 316 NOTE: DW-10HS should NOT be installed on top of insulation.
1-3/4 RING A153-D HOT DIP COIL ROOFING NAILS similar to Maze CLWR104A Steelhead GCR5DRHD . All our ASTM A153-D Hot Dip Nails meet and/or exceed the United States standard for Hot Dip Zinc Mass Coating of ASTM A153 class D Fasteners. HDG grade nails are first cut to length and heads formed from a large spool of brite steel wire rod.
This is a list of ASTM International standards. Standard designations usually consist of a letter prefix and a sequentially assigned number. This may optionally be followed by a dash and the last two digits of the year in which the standard was adopted. Prefix letters correspond to the following subjects: A = Iron and Steel Materials
Tambin puede elegir de doblez, soldadura y corte astm a153, as como de cortadora de hojas, haciendo tubos y pipa flida astm a153.Y si astm a153 es galvanizado. Hay proveedores de 280 astm a153, principalmente ubicados en Asia. Los principales pases o regiones proveedores son China, que proveen el 100% de astm a153, respectivamente.
Electro-galvanized (EG), conforming to ASTM B633 Type III SC1; Hot-dipped galvanized (HG), conforming to ASTM A123 or A153 (hardware) Green Powder Coat (GR), conforming to commercial standards for Powder Coating, and plain (PL) Unistrut Defender (DF), conforming to ASTM A1059 or A1046; APPLICATION
Unistrut P4007 P4008 P4009 P4010 Spring Nuts. Unistrut Channel Nuts with Springs allow you to easily attach Unistrut Channel and Fittings to one another. To be used with the following channels: P3300, P4000, P4400, P4520 and P4100.
ASTM A126 Or . ASTM A197 ASTM A153 : ASME B16.14 . WW-P-471 * ASTM B633 Type I, SC 4 may be used as an alternate zinc coating per ASME B16.14 . Cast Iron Plugs Bushings Pressure-Temperature Ratings Temperature ( F) Working Pressure (psi) Class 125 Class 250 -20 to 150 175 400 200 165 370 250 150 340 300 140 310 350 (1)125 300 400 (2) 250
Hot-Dip Galvanized material will meet or exceed ASTM A153 and/or ASTM F2329. Galvanized nuts are over tapped per ASTM A563. Typical hardness is HRC 24-35 for diameters up to 1 1/2 inches, HRB 95 - HRC 35 for diameters over 1 1 1/2 inches. Proof load strength is 175,000 psi. A194 2H Heavy Hex Nuts. Nominal Size or Basic.
ASTM A153/A153M - Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware. Published by ASTM on November 1, 2016. This specification covers zinc coatings applied by the hot-dip process on iron and steel hardware. The hot-dip galvanizing process consists of parts being immersed in molten zinc for a sufficient...
ASTM A563 Bolts, ASTM A563 Anchor Fasteners, ASTM A563 Nuts, ASTM A563 Socket Screw, ASTM A563 Washers Manufacturer, Exporter Suppliers. JF Engineering has been manufacturing ASTM F563 Fasteners since 2004 shipped to more than 60 Countries Like Argentina , Germany , Mexico , Vietnam , Indonesia , USA , Saudi Arabia , UAE , Egypt , Turkey ...